Note: All swatch colors shown in this brochure are approximations of the actual paint color in the can. 800-221-4466 WWW.PETTITPAINT.COM PREP & CONDITIONING PRODUCTS EZ-Tex® 7100 is an easy to use epoxy repair compound where a high strength, waterproof, permanent repair is needed. This unique formula creates a tenacious bond to most surfaces. Its buttery consistency will not sag or shrink and is excellent for filling cracks, gouges and voids. A 1:1 ratio makes mixing easy. EZ-Tex can be sanded, drilled, tapped, screwed, and painted once cured. EZ-Wood Sealer 2018 is used to seal all types of raw wood prior to painting and varnishing. The sealer acts as a moisture barrier layer to prevent peeling and excessive absorption of vehicle from topside primers, paints, or varnishes. It uniformly seals and satisfies the absorbancy of all woods, including teak and mahogany. EZ-Fair Epoxy Fairing Compound 7050 is a lightweight, two-part epoxy putty designed for filling and smoothing surface imperfections above and below the waterline. The special resins used in EZ-Fair impart a high degree of water and chemical resistance to the product, making it an integral part of the Pettit Gelcoat Blister Repair System. EZ-Fair is the product of choice for fairing metal keels or any underwater surface. Flexpoxy 7076 is a two-part epoxy resin that does not sag, run, or shrink. Its thick formula allows it to fill large cavities in a single application. When cured, it remains flexible making it ideal for environments that require flex, such as keel joint repairs. Its low odor formula is resistant to chemicals and is safe to use above and below the waterline. Flexpoxy creates a superior bond to all epoxies, polyester resins, metals and wood. It can be sanded, machined, cut, filed, planed, drilled, tapped, or nailed, making it perfect for filling, filleting, forming, fairing, and fastening. Flexpoxy can be molded and shaped during application and is easily tinted with paints and stains. EZ-Prime (new aerosol packaging available!) is a multi-purpose primer designed for use as a base coat whenever the surface to be painted is aged, cracked, checked, pitted, or in any way less than smooth. It can be applied to fiberglass, wood, properly etched metal, and previously painted surfaces. EZ-Prime fills imperfections, dries quickly, and is easy to sand. Compatible with EZ-Poxy Performance Enhancer. WHITE 6149 Bio-Blue Hull Surface Prep 92 is a powerful blend of cleaning agents and silica grit that de-waxes, etches, cleans, and prepares bare fiberglass for painting, regardless of the boat’s age. This solvent-free product is designed to provide an easy and trouble-free method of removing unwanted contaminants, grease, wax, dirt, and mold release agents from fiberglass surfaces prior to painting. Rustlok® Metal Primer 6980 is an easy-to-apply, moisture and corrosion-proof primer for use on all cast iron, aluminum, and steel surfaces, including galvanized and stainless steel. Its water impervious barrier offers excellent adhesion and corrosion protection, even over rusted surfaces. Rustlok Metal Primer is recommended any time an easy-to-apply, anti-corrrosive barrier coat is desired. AlumaProtect 4400/4401 is a two-part strontium chromate primer designed to form the ideal barrier coat over roughed bare aluminum. AlumaProtect provides maximum resistance to fresh or salt water, thus eliminating corrosion. This product is intended to be used as a primary coat over bare aluminum hulls and outdrives. PAINT STRIPPER & THINNER EZ Speed Strip™ 125 maximum strength marine coating remover will quickly and efficiently strip all types of finishes from fiberglass to metal surfaces. This product is effective on topside and baked enamels, acrylics, lacquers, polyurethanes, epoxies, antifouling paints and primers. EZ Speed Strip is non-corrosive to metals under normal exposure time. Its gel consistency allows it to work on horizontal and vertical surfaces without dripping or sagging. 120 Brushing Thinner is a general purpose thinner. Many paints when stored for some time before use, will increase in viscosity and should be thinned. 120 Brushing Thinner evaporates at a moderate rate and is completely out of the paint film in several hours. Up to 10% is the normal recommended usage, although some very hot and windy days may require more thinner.
RkJQdWJsaXNoZXIy MzI5NTg=