All prices are subject to change. Please refer to our website for most recent pricing. 21 Construction & Repair Laminating Consumables Construction & Repair Laminating Consumables | Fitting | Nylon US Plastics An economical, easy method for securing tubing to fittings. With the hose in place on the fitting, select a Handy Clamp that provides a snug fit with one to three teeth engaged. • One (1) Ordering Unit is: Each • Minimum Order Quantity: 1 Fitting BWS Part Number Description Price USP 65785 Nylon Handy Clamp - 0.713” - 0.843” $0.92 Laminating Consumables | Fitting | Valve PRO-VAC A polyethylene double O-ring infusion valve. Can be used up to 212°F. • One (1) Ordering Unit is: 25 Pieces • Minimum Order Quantity: 1 Pack BWS Part Number Description Price PVAC PV-70-12 Infusion Valve 12 mm (.47”) $107.00 PVAC PV-70-18 Infusion Valve 18 mm (.71”) $121.76 Laminating Consumables | Fitting | Connector AIRTECH Resin infusion connector provides inexpensive and efficient through bag connection for vacuum manifold and resin feed lines for low temperature resin infusion application. (use with 1/2’’ O.D. x 3/8’’ I.D. x 100 ft. tubing). • One (1) Ordering Unit is: Each • Minimum Order Quantity: 1 Connector BWS Part Number Description Price ART RIC1/2 1/2” Resin Infusion Connector $17.19 Laminating Consumables | Fitting | “T” PRO-VAC A polyethylene T-shaped connector for resin infusion. Can be used up to 212°F. • One (1) Ordering Unit is: 50 Pieces • Minimum Order Quantity: 1 Pack BWS Part Number Description Price PVAC PV-76-12 “T” Connector 12 mm (.47”) $59.03 Laminating Consumables | Resin Feed | Elevated PRO-VAC A steel coil resin feed wrapped in Pro-Vac Low-Flow Infusion Mesh (PV-50). This allows the resin feed to be elevated about the part when under vacuum to prevent part imperfections caused by resin feed lines. Can be used up to 250°F. • One (1) Ordering Unit is: Each • Minimum Order Quantity: 1 Feed BWS Part Number Description Price PVAC PV-68-40 Elevated Resin Feed - 40’ $152.48 Laminating Consumables | Resin Feed | Enka® PRO-VAC Enka 3D matrix infusion channel for fast resin flow. Increases efficiency and reduces infusion time. Provides steady flow speeds over large surfaces. Maximum use temperature of 302°F. • One (1) Ordering Unit is: Each • MinimumOrder Quantity: 1 Feed = 328’ BWS Part Number Description Price PVAC PV-66-50 Enka® Resin Feed - 2” x 328’ $500.69 PVAC PV-66-100 Enka® Resin Feed - 4” x 328’ $660.45 Laminating Consumables | Tacky Tape | Sealant Tape Construction & Repair Tacky Tape SM5142 is a sealant tape designed for vacuum bagging and autoclave operations. Its aggressive initial tack can maintain an air-tight seal during the cure cycle, yet strip clean from the tool, with virtually no trace of residue. • One (1) Ordering Unit is: Each • Minimum Order Quantity: 1 Roll = 25’ BWS Part Number Description Price NORT ST-SM5142-400-BYL Tacky Tape, Yellow - 1/2” x 1/8” x 25’ $13.07 Laminating Consumables | Tape | General Purpose Tape PRO-VAC PV-80 General Purpose Sealant Tape is designed for vacuum infusion, wet layup, and bag-to-bag (envelope bagging) processes. It performs best at room temperature ,+68°F, and has a maximum use temperature of 302°F. If the tape is too cold the tack levels will be dramatically reduced. Compatible with most vacuum films and tool surfaces. • One (1) Ordering Unit is: Each • Minimum Order Quantity: 1 Roll = 50’ BWS Part Number Description Price PVAC PV-80-3 General Purpose Sealing Tape - 1/2” x 50’ $22.14
RkJQdWJsaXNoZXIy MzI5NTg=